Point 1. Synchronous belt a hruihrual hma lutuk .
1. Driven wheel leh driven load-a inertia force chu ngaihtuah a ni lo.
2、 Load a lian lutuk emaw, accident vangin passive wheel a ding a, chu chuan load force nasa takin a tipung a ni.
3、Pulley chu a te lutuk a, belt chu forcibly ben over a ni.
Chhanna dik:
1、a design siam that.
2. Design chu enfiah la, pulley chu a original minimum aiin ha tam zawk hmangin thlak rawh.
3, handling, storage, installation leh operation te hi a kimchangin hriat theih a ni a, fimkhur a ngai bawk.
Point 2. Synchronous belt belt edge wear .
1、Wheel parallelism hi phal a ni lo.
2、Earing rigidity nei lo.
3、Belt wheel-a retaining edge-a bebending.
4、Pulley diameter hi belt zau zawng aiin a te zawk.
Chhanna dik:
1、Pulley awmna tur chu calibrate rawh.
2、Bearing rigidity tihpun leh nghet taka siam.
3、retaining edge siam that emaw, thlak emaw.
4. Design chu enfiah rawh.
Point 3.Synchronous belt ha chunglam a inbel .
1、A phurrit a lian lutuk.
2、Belt tensioning force hi a lian lutuk.
3、Abrasive powder layer puitling tawh.
4、ei chuan wheel ha a ti a.
Chhanna dik:
1、a design siam that.
2、Belt tensioning force chu siamthat rawh.
3、Environment siam that leh protective cover tihpun.
4、ei thin, wheel light te siam that emaw, pulley thlak emaw.
Point 4. Synchronous belt ha a chhe .
Ha 1、ei thin.
2. Passive mechanical accident load a pung.
Chhanna dik:
1. Design chu enfiah rawh.
2、Ensioning force dik tak siamrem rawh.
3、Pulley diameter tihpun leh ha tihpun.
4、Exclude Passive Mechanical Failure .
Point 5. Synchronous belt chu rubber backing wear leh cracking nen a inzawm a ni.
1、Pawn lam tensioning wheel rotation a block.
2、Outer tensioning wheel misalignment.
3. Machinery frame chu en rawh.
4、eng hun rei tak chhunga temperature hniam zawk state.
Chhanna dik:
1、Thil tension wheel bearings siam that emaw thlak emaw.
2、Thil tension wheel awmna tur dik tak a ni.
3、eng mechanical parts te enfiah leh siamthat.
4、Ambient temperature a ti ṭha thei.
Point 6. Backing hmanga tih nem.
1、A lumna sang ber .
2、Thingtlang tan a ni.
3、ei thin oil.
Chhanna dik:
1、Ambient temperature a ti ṭha thei.
2、Ensioning wheel chu enfiah la, siamrem rawh.
3、Oil-ah hian innghat suh la, oil-resistant synchronous belt pawh thlak suh.
Point 7. Belt longitudinal cracking .
1、Pulley kil khat atanga timing belt a kal a.
2、Synchronous belt chuan pulley retaining edge chu a roll up a.
Chhanna dik:
1、Belt pulley awmna tur chu siamrem rawh.
2、Enhance the bearing rigidity leh nghet taka siam.
Point 8. Taksa tensile tak tak a tihchhiat dan part .
1、Tinging belt a load leh a chhuah theih loh.
2, a chhe tawh emaw, a hnah hring leh a hnah hring (sharp and sharp residue) nen a pawlh a.
Chhanna dik:
1、Synchronous belt load leh unload dan dik tak.
2、Environment siam that. Protective cover a dah tel bawk.
Point 9. Run laiin thawm ri tam lutuk .
1、Tnensioning force of synchronous belt hi a lian lutuk.
2. Axes pahnih te chu parallel misalignment an nei a.
3、Pulley diameter aiin timing belt zau zawng hi a lian zawk a ni.
4、A phurrit a lian lutuk.
5、Elt leh pulley teeth te hi a fit tha lo hle.
Chhanna dik:
1、Thil tensioning wheel a hniam zawk (lomping teeth a awm lo).
2、Belt pulley awmna tur chu siamrem rawh.
3、A design chu a ti ṭha thei.
4、A design siam that.
5、A timing belt leh pulley te chu enfiah rawh.
Point 10.Belt pulley ha hak tur a ni.
1、A phurrit a lian lutuk.
2、Synchronous belt tension hi a lian lutuk.
3、Pulley-a thil awm chu a tha lo.
4、Abrasive dust adulteration.
Chhanna dik:
1、a design siam that.
2、engtikah chuan tensioning force a hniam zawk.
3、A chung lamah hardening treatment hmangin hard material hmang ang che.
4、Environment siam that leh protective cover tihpun.
