Synthetic Rubbers: A nihna leh a thatna chipchiar tak tak, a hmanna tur leh a hman dan tur te

1. Fluororubber (FKM) a ni a, a man pawh a to hle.

• Thil neih:

• A lumna a nasa lutuk (-20°C atanga +250°C thleng).

• Oil, fuel, solvent, acid leh base te laka invenna danglam tak.

• Tensile chakna sang, compression set hniam, leh chemical stability tha tak a nei bawk.

• meialh laka inven theih leh ozone laka inven theih a ni.

• A thatna:

• Chemical leh pressure sang tak tak awmna hmun a tuar thei.

• Aerospace leh automotive application-a service dam rei tawh.

• Dilna: 1.1.

• Aircraft fuel system seal, O-rings, leh gasket te.

• Automotive transmission seal te, engine hose te, leh turbocharger component te a awm bawk.

• Chemical processing hmanrua lining leh gasket te.

2. Chloroprene rubber (CR) a ni.

• Thil neih:

• Oil resistance moderate (natural rubber aiin a tha zawk mahse FKM aiin a tlem zawk).

• Flame retardant leh mahni inhnukdawk theihna nei.

• Khaw lum leh khaw vawt laka invenna tha (UV, ozone, leh tuihna).

• Temperature hniam (-40°C atanga +120°C) ah pawh a inthlak thei.

• A thatna:

• Cost-effective leh processing awlsam tak (extrusion/molding) a ni.

• Mechanical strength sang tak leh abrasion resistance.

• Dilna: 1.1.

• Wet suit, gloves, leh industrial hose te pawh a awm bawk.

• pheikhawk leh sakna tur adhesives.

• Cable jacket leh roofing membrane te a awm bawk.

3. Hydrogenated nitrile rubber (HNBR) a ni.

• Thil neih:

• NBR nena khaikhin chuan heat resistance (+150°C thleng) a tichak zawk.

• Oils, hydraulic fluids, leh amine te laka invenna tha zawk.

• Tensile chakna sang tak leh fatigue resistance.

• Gas-te tana permeability hniam.

• A thatna:

• Hun rei tak chhung chemical na tak tak a tawh avangin elasticity a nei reng.

• Extreme condition-ah chuan NBR aiin a dam rei zawk.

• Dilna: 1.1.

• Oil leh gas drilling hmanrua (packers, seals) te.

• Automotive timing belt, fuel injection components, leh turbocharger seal te pawh a awm bawk.

• Industrial hydraulic cylinder te pawh a awm bawk.

4. Silicone rubber (VMQ) a ni.

• Thil neih:

• Ultra-wide temperature range (-60°C atanga +200°C) a ni.

• elasticity sang (1000% elongation thleng) a ni.

• Electrical insulation tha tak leh thermal stability tha tak a nei bawk.

• Biocompatible leh inert a ni.

• A thatna:

• Cryogenic leh high-temperature environment-ah pawh flexibility a nei reng.

• UV, ozone, leh khaw lum leh khaw vawt laka inven theih a ni.

• Dilna: 1.1.

• Damdawi hmanrua (catheter, implant) te pawh a awm thei.

• Electronic components (inculator, keypad) te pawh a awm thei.

• Oven leh engine siamna tur gasket sang tak tak a awm bawk.

5. Fluorosilicone rubber (FVMQ) a ni.

• Thil neih:

• FKM chemical resistance leh VMQ flexibility te a hmang dun a ni.

• A lumna hmun: -50°C atanga +230°C thleng a ni.

• Fuel, lubricant leh hydraulic fluid te laka inven theih a ni.

• Compression set hniam leh resilience tha tak a nei bawk.

• A thatna:

• High-temperature leh low-temperature extreme-ah te a thawk thei.

• Aviation fuel-a swelling do thei.

• Dilna: 1.1.

• Aircraft fuel system components (valve, seals) te.

• Tuipui thuk takah tui hnuaia awm gasket leh connector te.

• Automotive sensor leh emission control system te a awm bawk.

6. Ethylene propylene diene monomer (EPDM) a ni a, a man pawh a tlawm hle.

• Thil neih:

• Ozone leh khaw lum leh khaw vawt laka inven theihna ropui tak a ni.

• Dielectric chakna sang tak leh tui laka inven theihna.

• A lumna hmun: -50°C atanga +150°C thleng a ni.

• Gas permeability hniam tak a awm.

• A thatna:

• Pawn lama hmanna atan chuan a man tlawm ber.

• Vibration damping tha tak leh noise reduction tha tak a ni.

• Dilna: 1.1.

• Automotive khaw lum leh khaw vawt, radiator hose, leh windshield seal te pawh a awm bawk.

• roofing membrane leh pond liners te a awm bawk.

• Electrical cable insulation leh power transmission belt te a awm bawk.