Synthetic Rubbers: A nihna chipchiar tak, a thatna leh a hman dan

1. Fluororubber (FKM) hmanga siam a ni.

• Thil neih:

• A lumna nasa tak (-20°C atanga +250°C thleng) a ni.

• Oil, fuel, solvent, acid leh base te laka a invenna danglam tak.

• Tensile strength sang tak, compression set hniam tak, leh chemical stability tha tak a nei bawk.

• Meialh laka invenna leh ozone laka invenna a ni.

• A thatna te: 1.1.

• Chemical nasa tak leh pressure sang tak awmna hmunah a tuar thei.

• Aerospace leh automotive application-ah service life rei tak a awm.

• Dilna: 1.1.

• Vanlawng fuel system seal, O-ring, leh gasket te a awm bawk.

• Automotive transmission seal, engine hose, leh turbocharger component te a awm bawk.

• Chemical processing hmanrua lining leh gasket te a awm bawk.

2. Chloroprene Rubber (CR) hmanga siam a ni.

• Thil neih:

• Oil resistance moderate (natural rubber aiin a tha zawk mahse FKM aiin a tlem zawk).

• Flame retardant a ni a, mahni inthiar theihna a nei bawk.

• Khaw lum leh khaw vawt laka invenna tha (UV, ozone, leh tuihna).

• Temperature hniam (-40°C atanga +120°C) ah pawh a inthlak thei.

• A thatna te: 1.1.

• Processing (extrusion/molding) awlsam tak leh man tlawm zawk.

• Mechanical strength sang tak leh abrasion resistance sang tak a nei bawk.

• Dilna: 1.1.

• Wet suit, kutkawr, leh industrial hose te a awm bawk.

• Kekawr leh sakna atana hman tur adhesives.

• Cable jacket leh roofing membrane te a awm bawk.

3. Hydrogenated Nitrile Rubber (HNBR) hmanga siam chhuah a ni.

• Thil neih:

• NBR nena khaikhin chuan heat resistance (+150°C thleng) a tichak zawk.

• Oil, hydraulic fluid, leh amine te laka invenna tha zawk.

• Tensile chakna sang tak leh hahna tuar thei.

• Gas-te laka permeability hniam tak.

• A thatna te: 1.1.

• Hun rei tak chhung chemical na tak tak a tawh avangin elasticity a nei reng.

• Thil awmdan khirh takah chuan NBR aiin dam rei zawk.

• Dilna: 1.1.

• Oil leh gas laihchhuahna hmanrua (packer, seal).

• Automotive timing belt, fuel injection components, leh turbocharger seal te pawh a awm bawk.

• Industrial hydraulic cylinder te pawh a awm bawk.

4. Silicone Rubber (VMQ) hmanga siam a ni.

• Thil neih:

• Ultra-wide temperature range (-60°C atanga +200°C thleng) a ni.

• elasticity sang (1000% elongation thleng) a ni.

• Electrical insulation tha tak leh thermal stability tha tak a nei bawk.

• Biocompatible leh inert tak a ni.

• A thatna te: 1.1.

• Cryogenic leh high-temperature environment-ah pawh flexibility a vawng reng.

• UV, ozone, leh khaw lum leh khaw vawt laka invenna a ni.

• Dilna: 1.1.

• Damdawi hmanrua (catheter, implant) te.

• Electronic components (insulator, keypad) te pawh a awm bawk.

• Oven leh engine atana hman tur gasket temperature sang tak.

5. Fluorosilicone Rubber (FVMQ) hmanga siam a ni.

• Thil neih:

• FKM chemical resistance leh VMQ flexibility te a inzawm khawm a ni.

• A lumna hmun: -50°C atanga +230°C thleng a ni.

• Fuel, lubricant leh hydraulic fluid te laka inven theih a ni.

• Compression set hniam leh resilience tha tak a ni.

• A thatna te: 1.1.

• High-temperature leh low-temperature extreme-ah te a thawk thei.

• Aviation fuel-a swelling lakah a do thei.

• Dilna: 1.1.

• Vanlawng fuel system component hrang hrang (valve, seal) te.

• Tuipui thuk lama tui hnuaia awm gasket leh connector te.

• Automotive sensor leh emission control system te a awm bawk.

6. A rilru a buai em em a, a rilru a hah em em bawk a. EPDM .

• Thil neih:

• Ozone leh khaw lum laka invenna ropui tak.

• Dielectric chakna sang tak leh tui tlakchhamna sang tak.

• A lumna hmun: -50°C atanga +150°C thleng a ni.

• Gas permeability a hniam.

• A thatna te: 1.1.

• Pawn lama hmanna atan chuan a man tlawm ber.

• Vibration damping tha tak leh noise reduction tha tak a ni.

• Dilna: 1.1.

• Automotive weatherstripping, radiator hose, leh windshield seal te a awm bawk.

• Roofing membrane leh pond liners te a awm bawk.

• Electrical cable insulation leh power transmission belt te a awm bawk.